hrhllogo
dynamat logo

Dynamat Xtreme Door Kit Installation

These installation instructions will guide you through the proper installation of the Dynamat Xtreme Door Kit.

NOTE: If you are unsure about your installation abilities, have an Authorized Dynamat Dealer perform the installation.

For optimal performance, observe the following installation steps:

10435_door_kit_xtreme

Click on Images below
for larger views

Step 1

Remove the factory door panel. Refer to a shop manual of your vehicle for detailed information on how to disassemble your vehicle.

1removing_panelsm

Step 2

Remove your speaker. Refer to your shop manual for removal instructions. At this time also remove the plastic moisture barrier on the door panel. The moisture barrier will not be reused and can be discarded.

TIP: Use the moisture barrier as a template for cut out holes for the door handle and wires.

2removing_speakersm

Step 3

Thoroughly clean the mounting surface with a quick-drying, residue-free solvent. Remove all dirt, grease, oil, wax, moisture and rust to ensure a permanent bond between the Dynamat and the mounting surface.

3cleaning_inner_panelsm

Step 4a (optional)

For superior sound damping and noise reduction, apply Dynamat to the outer door skin. Cut Dynamat pieces to fit outer door skin and apply with a Dynamat roller tool.

Note: The Dynamat Door kit contains coverage for 1 door with outer & inner skin OR two doors with inner skin only.

4-1tacoma_door_outerskin1

Step 4

Position one of the 12” x 36” pieces on the bottom of the door. Cut off any excess with the Dynamat Switch-A-Blade razor knife or scissors. Also, make cuts to allow any wire or harnesses to be pulled through the Dynamat.

4-2installing_innerpanel

Step 5

Apply the Dynamat to the mounting surface with a Dynamat roller tool. Take the roller tool and work the Dynamat into all contours of the metal panel.   Start at one side of the material and work your way across. This will maximize contouring and promote the best adhesion and performance.

WARNING: Make sure your installation of Dynamat does not interfere with the normal operation of the door.

5installing_innerpanel2

Step 6

Position the second 12” x 36” piece on the top of the door.   Cut off any excess with the Dynamat Switch-A-Blade razor knife or scissors.   Mark and make the cuts for the door handle and items that require access through the Dynamat.

To ensure lasting adhesion and maximum damping effect, remove air pockets formed under the Dynamat by poking them with a razor knife and removing the air with a roller tool.

6installing_innerpanel3

Step 7

Take a roller tool and work the Dynamat into all contours of the metal panel. Start at one side of the material and work your way across. Make small X incisions in the Dynamat to allow access for door rods and mounting tabs. Cover the entire panel including the openings.

TIP: Only cut out the necessary areas. Minimizing the amount of openings will maximize the amount of noise blocked.

7installing_innerpanel4

Step 8

Dynamat installation is complete. Make sure the Dynamat does not interfere with the normal operation of the door. Test door functionality and fix any problems that might occur before reinstalling the door panel.

8dynamat_finished

Step 9

Reinstall the door panel. Refer to a shop manual of your vehicle for detailed information on how to reassemble your door panel.

9door_panel_finish

For More Infor Contact Dynamat

DYNAMIC CONTROL OF NORTH AMERICAN, INC
3042 Symmes Road
Hamilton, Ohio 45015 USA
Phone: (513) 860-5094
Fax: (513) 860-5095
US SALE / DEALER INFO: sales@dynamat.com
TECHNICAL INFO: technical@dynamat.com
WEB SITE: www.dynamat.com

line12

 

 

 

line12

[HRHL Home] [2009 Show Coverage] [Barn & Field Cars] [Blast to the Past]
[Book Reviews] [Build Articles] [Buyers Guide] [Classifieds] [Club Directory]
[Event Listings] [From our Friends] [Garage Shots] [Guest Columnists] [Hotrod MD]
[New Products] [Newsletter Archive] [Order a Catalog] [Our Heroes] [Press Releases]
[Rodders Forum] [Rodders Row] [Shop Tours] [Vendor Directory] [Young Rodders]
[Advertising Information] [Modern Rods] [Site Map] [Stolen] [EMAIL]

Copyright 1999 - 2009 Hot Rod Hot Line All Rights Reserved
No Portion May Be Used Without Our Written Permission
Contact Us Toll Free (877) 700-2468 or (208) 562-0470
230 S. Cole Rd, Boise, ID 83709