Header__ARTICLEShorter

Garage Shots
of Larry Henderson”s
51 Henry J

built by Super Rides by Jordan In Escondido, Ca

I thought I would send you some pics of a 51 Henry J that I am having built by Super Rides by Jordan In Escondido Ca. I Found the car in Illinois in 05 and have been working on it for about a year. Using a ZZ4 crate motor with Barry Grant six shooter 3 deuce set up, Fat Man front clip, 700R trans, Ford 9" rear end, custom fab frame 4 link rear, Mercedes headlights, reshaped rear side windows, removed door vent windows, all body seams welded, and drip rails filled and rolled. Thought you might put this in your garage shots section. It is nice to see what others are building, it gives me lots of ideas. Thank you, Larry Henderson


Click on Photos to enlarge

db_110

 

db_210

 

db_310

 

db_410

 

db_510

 

db_62

 

db_710

 

db_84

 

db_92

 

db_102

 

db_112

 

db_122

’These three pictures are of the latest work being done on Larry Hendersons 51 Henry J which is the dash from a 50 chev going in

db_132

fitting new tail light rings with 58 chev lenses.

db_142

 

15

Latest 4 pics. Dash completed and installed. Air ride suspension going in. Tail light work almost complete, left light area re-shaped and right light area not done yet.

16

 

17

 

18

 

19

These three are Larry Henderson’s latest garage shot pics with air ride installed in front,

20

 rework of wheel wells for tire clearance when slammed to the ground. Larry

21

 

22

These next three pictures are street and performance chrome plated serpentine system being dry fit

23

 

24

air ride technologies system being installed.

25

A couple garage shots of the latest work being done. Rear roll pan work and front grille center section fabrication starting along with 68 Camaro front bumper temp. installed

26

 

27

Larry’s latest work is radiator support work, filling in hood center opening

28

 

29

 fabricating new grille center piece.

30

 

31

Here are two shots of inner fenders being made to accommodate the AC compressor and the alternator.

32

 

33

All Body modifications are getting close to being completed.

34

 

35

Here are two shots of inner fenders being made to accommodate the AC compressor and the alternator. All Body modifications are getting close to being completed.

36

 

37

a couple shots of each side of the front fenders. We raised the wheel openings just 1” higher that original but it makes a lot of difference in the turning radius with the air ride suspension.

38

 

39

Visited the car this morning and took a couple of shots. Completed Wheel openings after raising 1".

40

Reinforcing the hood and hood latch area work.

41

 

45

Front bucket seats from glide engineering arrived.

42

Seats from Glide Engineering arrived and are being dry fit.

43

Here are a few latest pics of what has been going on. Dash work and steering column installation.

44

 

46

Here are a few shots of the rear bumpers being made from aluminum then will be chrome plated.

47

 

48

 

50

Here is a few shots of work that has been started on the console

49

rear seating area. Still in the design process, just trial and error to see what works.

51

 

 

 

 

[2011 Show Coverage] [Barn & Field Cars] [Blast to the Past] [Book Reviews] [Build Articles] [Buyers Guide] [Classifieds] [Club Directory] [Event Listings] [From our Friends]
[Garage Shots] [Guest Columnists] [www.hotrodhotline.com/md] [New Products]
[Newsletter Archive] [Order a Catalog] [Our Heroes] [Press Releases]
[Rodders Forum] [Rodders Row] [Shop Tours] [Vendor Directory]
[Young Rodders] [Advertising Information] [Modern Rods]

Copyright 1999 - 2011 Hot Rod Hot Line All Rights Reserved
No Portion May Be Used Without Our Written Permission
Contact Us Toll Free (877) 700-2468 (US) or (208) 562-0470 (Outside US)
230 S. Cole Rd, Boise, ID 83709

mailbox