Header_300_DPI_TALL2900 wide
dynamat

Featured Product
from
Dynamat

Dynamat Xtreme Door Kit Installation

10435_door_kit_xtreme

These installation instructions will guide you through the proper installation of the Dynamat Xtreme Door Kit.
NOTE: If you are unsure about your installation abilities, have an Authorized Dynamat Dealer perform the installation.

For optimal performance, observe the following installation steps:

Step 1

Remove the factory door panel. Refer to a shop manual of your vehicle for detailed information on how to disassemble your vehicle.

removing_panel
a05

Step 2

Remove your speaker. Refer to your shop manual for removal instructions. At this time also remove the plastic moisture barrier on the door panel. The moisture barrier will not be reused and can be discarded.

TIP: Use the moisture barrier as a template for cut out holes for the door handle and wires.

removing_speaker
a05

Step 3

Thoroughly clean the mounting surface with a quick-drying, residue-free solvent. Remove all dirt, grease, oil, wax, moisture and rust to ensure a permanent bond between the Dynamat and the mounting surface.

cleaning_inner_panel
a05

Step 4a (optional)

For superior sound damping and noise reduction, apply Dynamat to the outer door skin. Cut Dynamat pieces to fit outer door skin and apply with a Dynamat roller tool.

Note: The Dynamat Door kit contains coverage for 1 door with outer & inner skin OR two doors with inner skin only.

tacoma_door_outerskin1
a05

Step 4

Position one of the 12” x 36” pieces on the bottom of the door. Cut off any excess with the Dynamat Switch-A-Blade razor knife or scissors. Also, make cuts to allow any wire or harnesses to be pulled through the Dynamat.

installing_innerpanel
a05

Step 5

Apply the Dynamat to the mounting surface with a Dynamat roller tool. Take the roller tool and work the Dynamat into all contours of the metal panel. Start at one side of the material and work your way across. This will maximize contouring and promote the best adhesion and performance.

WARNING: Make sure your installation of Dynamat does not interfere with the normal operation of the door.

installing_innerpanel2
a05

Step 6

Position the second 12” x 36” piece on the top of the door. Cut off any excess with the Dynamat Switch-A-Blade razor knife or scissors. Mark and make the cuts for the door handle and items that require access through the Dynamat.

To ensure lasting adhesion and maximum damping effect, remove air pockets formed under the Dynamat by poking them with a razor knife and removing the air with a roller tool.

installing_innerpanel3
a05

Step 7

Take a roller tool and work the Dynamat into all contours of the metal panel. Start at one side of the material and work your way across. Make small X incisions in the Dynamat to allow access for door rods and mounting tabs. Cover the entire panel including the openings.

TIP: Only cut out the necessary areas. Minimizing the amount of openings will maximize the amount of noise blocked.

installing_innerpanel4
a05

Step 8

Dynamat installation is complete. Make sure the Dynamat does not interfere with the normal operation of the door. Test door functionality and fix any problems that might occur before reinstalling the door panel.

dynamat_finished
a05

Step 9

Reinstall the door panel. Refer to a shop manual of your vehicle for detailed information on how to reassemble your door panel.

door_panel_finish

Get more details here

 

Dynamic Control of North America, Inc.
3042 Symmes Road
Hamilton, Ohio 45015 USA
Phone: (513) 860-5094
Fax: (513) 860-5095
Email: [email protected]
For additional support, email
[email protected]

Our Mission
Dynamic Control seeks to produce and deliver high quality acoustic solutions to the world with speed and accuracy, for better sound everywhere
About Us
Dynamic Control of North America, Inc. is a privately held corporation located in Hamilton, Ohio, USA. Established in 1989, the company markets acoustic environmental solutions for a broad range of industries.
Dynamat, a Dynamic Control brand, is recognized by consumers around the world as a quality product for solutions to unwanted noise and vibration. The Dynamat brand maintains the dominant marketshare in Car Audio and Automotive Restoration acoustic solutions. Dynamic Control also provides a broad range of unique product solutions for home acoustics, computers, appliances, and Original Equipment Manufacturers.
Our operations cover the United States of America serving over 3,000 storefronts. Dynamat is merchandised and promoted in large retailers such as Best Buy, Pep Boys most large regional Audio Retailers and Independent Specialty Car Audio Retailers.
Internationally, our products are represented in over 50 countries.

Visit us on the web:

 


You can see lots more articles at www.Hotrodhotline.com
or check out some of our many different  article sections

[HRHL Home] [2011 Show Coverage] [Classifieds] [Press Releases]
[Advertising Information] [Buyers Guide] [Vendor Directory]
 [Barn & Field Cars] [Biker Hotline] [Blast to the Past] [Book Reviews]
[Build Articles] [Club Directory] [Event Listings] [From our Friends]
[Garage Shots] [Guest Columnists] [Hotrod MD] [Landspeed Racing]
[Modern Rods] [New Products] [Newsletter Archive] [Order a Catalog]
[Our Heroes] [Rodders Forum] [Rodders Row] [Shop Tours] [Site Map]
[Stolen] [Tech] [Vanity Plates] [Young Rodders] [EMAIL]


Copyright 1999 - 2011 Hot Rod Hot Line All Rights Reserved
No Portion May Be Used Without Our Written Permission
Contact Us Toll Free (877) 700-2468 (US) or (208) 562-0470 (Outside US)
230 S. Cole Rd, Boise, ID 83709