VIP Sponsors

Sponsors

Dynamat Xtreme Door Kit Installation

 

 

Dynamat Xtreme Door Kit Installation

10435_door_kit_xtreme

These installation instructions will guide you through the proper installation of the Dynamat Xtreme Door Kit.
NOTE: If you are unsure about your installation abilities, have an Authorized Dynamat Dealer perform the installation.

For optimal performance, observe the following installation steps:

 

Step 1

Remove the factory door panel. Refer to a shop manual of your vehicle for detailed information on how to disassemble your vehicle.

 
  removing_panel
  a05
 

Step 2

Remove your speaker. Refer to your shop manual for removal instructions. At this time also remove the plastic moisture barrier on the door panel. The moisture barrier will not be reused and can be discarded.

TIP: Use the moisture barrier as a template for cut out holes for the door handle and wires.

 
  removing_speaker
  a05
 

Step 3

Thoroughly clean the mounting surface with a quick-drying, residue-free solvent. Remove all dirt, grease, oil, wax, moisture and rust to ensure a permanent bond between the Dynamat and the mounting surface.

 
  cleaning_inner_panel
  a05
 

Step 4a (optional)

For superior sound damping and noise reduction, apply Dynamat to the outer door skin. Cut Dynamat pieces to fit outer door skin and apply with a Dynamat roller tool.

Note: The Dynamat Door kit contains coverage for 1 door with outer & inner skin OR two doors with inner skin only.

 
  tacoma_door_outerskin1
  a05
 

Step 4

Position one of the 12” x 36” pieces on the bottom of the door. Cut off any excess with the Dynamat Switch-A-Blade razor knife or scissors. Also, make cuts to allow any wire or harnesses to be pulled through the Dynamat.

 
  installing_innerpanel
  a05
 

Step 5

Apply the Dynamat to the mounting surface with a Dynamat roller tool. Take the roller tool and work the Dynamat into all contours of the metal panel. Start at one side of the material and work your way across. This will maximize contouring and promote the best adhesion and performance.

WARNING: Make sure your installation of Dynamat does not interfere with the normal operation of the door.

 
  installing_innerpanel2
  a05
 

Step 6

Position the second 12” x 36” piece on the top of the door. Cut off any excess with the Dynamat Switch-A-Blade razor knife or scissors. Mark and make the cuts for the door handle and items that require access through the Dynamat.

To ensure lasting adhesion and maximum damping effect, remove air pockets formed under the Dynamat by poking them with a razor knife and removing the air with a roller tool.

 
  installing_innerpanel3
  a05
 

Step 7

Take a roller tool and work the Dynamat into all contours of the metal panel. Start at one side of the material and work your way across. Make small X incisions in the Dynamat to allow access for door rods and mounting tabs. Cover the entire panel including the openings.

TIP: Only cut out the necessary areas. Minimizing the amount of openings will maximize the amount of noise blocked.

 
  installing_innerpanel4
  a05
 

Step 8

Dynamat installation is complete. Make sure the Dynamat does not interfere with the normal operation of the door. Test door functionality and fix any problems that might occur before reinstalling the door panel.

 
  dynamat_finished
  a05
 

Step 9

Reinstall the door panel. Refer to a shop manual of your vehicle for detailed information on how to reassemble your door panel.

 
  door_panel_finish

Get more details here : www.dynamat.com
 


 

Dynamat is the pro's choice for turning Hot Rods into cool, quiet, and comfortable rides. Dynamat is the world's leading product for eliminating unwanted noise, vibration, and heat. Dynamat offers a complete product line of performance automotive and restoration products including Dynamat Xtreme, Extremeliner, and Tac Mat. All of our products are engineered and scientifically tested in our "Real World" research and development lab. Take it from pro's like Posie's and Bobby Alloway . . . no project is complete without Dynamat - the ultimate automotive accessory. As seen on Overhaulin' & Rides! Dynamat is sold in more than 5000 locations worldwide. For more information, visit www.dynamat.com.

Dynamic Control of North America, Inc.
Phone: (513) 860-5094
Fax: (513) 860-5095
Email: [email protected]
For additional support, email
[email protected]